Electroic Supply Chain Solutions as most people know is a leading advocate on the education to Combat Counterfeits and has attended this course 2 times at NASA's Quality Leadership Forum. The Introduction to AS5553 and Counterfeit Electronic Parts Avoidance Training we feel is a must to all companies looking to mitigate the risks associated with the purchase of electronic components. ESCS President Matthew Heaphy III is one of the G-19 members that authored the AS5553 standard and maintains the web site http://www.as5553.info/ to explain the many benefits of the new standard. ESCS strongly urges any who can attend this event to make plans early as this course shall fill up fast.
On-siteDelivery
OpenEnrollment
I.D.# C0950
Printable DescriptionDuration: 1 Day
November 10, 2009 (8:30 a.m. - 4:30 p.m. ) - Seattle, Washington
Hotel & Travel Information
Counterfeit electronic parts have been found in almost every sector of the electronics industry and continue to be an increasing threat to electronic hardware. This threat poses significant performance, reliability and safety risks. Aerospace industry organizations, in particular, must produce and continually improve safe and reliable products that meet or exceed customer and regulatory authority requirements. The SAE AS5553 standard was created in response to the significant and increasing volume of counterfeit electronic parts entering the aerospace supply chain and standardizes requirements, practices and methods for counterfeit parts risk mitigation. The resulting document presents solutions to address counterfeit electronic parts issues across a large cross-section of the electronics industry. This comprehensive one-day seminar introduces participants to AS5553 and specifically addresses counterfeit part risk mitigation methods in electronic design and parts management, supplier management, procurement, part verification, material control, and response strategies when suspect or confirmed counterfeit parts are discovered. The seminar will provide information and guidance in each of these key requirement areas. The latter part of the course will highlight counterfeit detection techniques and part compliance verification methods. Several examples of counterfeit parts will be reviewed in detail. The course will conclude with a hands-on learning exercise in identifying, under a microscope, characteristics that can be found in counterfeit electronic parts. To accomplish this, attendees are encouraged to bring a personal laptop computer. The instructors will provide a limited number of digital microscopes and electronic parts.
In addition to the seminar handout, a copy of the AS5553-Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition standard is provided to each registrant.
Learning ObjectivesBy attending this seminar, you will be able to:
Characterize and describe the threat of counterfeit electronic parts
Identify the characteristics of an effective Counterfeit Parts Control Plan
Demonstrate one of the first steps in verification of purchased product (inspection techniques for counterfeit parts)
Recognize suspect counterfeit parts
Who Should AttendThis seminar will benefit a wide range of individuals and experience levels across the electronics industry and supply chain. Anyone who designs, specifies, buys, receives, assembles and tests electronic hardware will benefit from this seminar. This includes electronic design engineers, parts engineers, quality assurance engineers, buyers, auditors, inspectors, assemblers, electronic test engineers, microelectronic non-destructive test engineers, destructive test analysts, and supplier managers. Additionally, this seminar will benefit individuals in various levels of management that influence electronic hardware.
PrerequisitesNone -Topical Outline
Introduction AS5553
Terms and definitions
Magnitude and impact of counterfeiting
Counterfeit electronic part examples
G-19 Committee and its challenges
AS5553 structure
Requirements
Counterfeit electronic parts control plan
Parts availability
Purchasing processes
Procurement contract requirements
Verification of purchased product
Control of suspect or confirmed counterfeit parts
Reporting
Future G-19 plans
Counterfeit Parts Recognition
Terms and definitions
Types of counterfeits
E-Waste
Documentation review
Slides of counterfeit parts and their features
Non-destructive and destructive testing for counterfeits
Hands-on inspection with microscopes
Closing
Assessment
Evaluations
On-siteDelivery
OpenEnrollment
I.D.# C0950
Printable DescriptionDuration: 1 Day
November 10, 2009 (8:30 a.m. - 4:30 p.m. ) - Seattle, Washington
Hotel & Travel Information
Counterfeit electronic parts have been found in almost every sector of the electronics industry and continue to be an increasing threat to electronic hardware. This threat poses significant performance, reliability and safety risks. Aerospace industry organizations, in particular, must produce and continually improve safe and reliable products that meet or exceed customer and regulatory authority requirements. The SAE AS5553 standard was created in response to the significant and increasing volume of counterfeit electronic parts entering the aerospace supply chain and standardizes requirements, practices and methods for counterfeit parts risk mitigation. The resulting document presents solutions to address counterfeit electronic parts issues across a large cross-section of the electronics industry. This comprehensive one-day seminar introduces participants to AS5553 and specifically addresses counterfeit part risk mitigation methods in electronic design and parts management, supplier management, procurement, part verification, material control, and response strategies when suspect or confirmed counterfeit parts are discovered. The seminar will provide information and guidance in each of these key requirement areas. The latter part of the course will highlight counterfeit detection techniques and part compliance verification methods. Several examples of counterfeit parts will be reviewed in detail. The course will conclude with a hands-on learning exercise in identifying, under a microscope, characteristics that can be found in counterfeit electronic parts. To accomplish this, attendees are encouraged to bring a personal laptop computer. The instructors will provide a limited number of digital microscopes and electronic parts.
In addition to the seminar handout, a copy of the AS5553-Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition standard is provided to each registrant.
Learning ObjectivesBy attending this seminar, you will be able to:
Characterize and describe the threat of counterfeit electronic parts
Identify the characteristics of an effective Counterfeit Parts Control Plan
Demonstrate one of the first steps in verification of purchased product (inspection techniques for counterfeit parts)
Recognize suspect counterfeit parts
Who Should AttendThis seminar will benefit a wide range of individuals and experience levels across the electronics industry and supply chain. Anyone who designs, specifies, buys, receives, assembles and tests electronic hardware will benefit from this seminar. This includes electronic design engineers, parts engineers, quality assurance engineers, buyers, auditors, inspectors, assemblers, electronic test engineers, microelectronic non-destructive test engineers, destructive test analysts, and supplier managers. Additionally, this seminar will benefit individuals in various levels of management that influence electronic hardware.
PrerequisitesNone -Topical Outline
Introduction AS5553
Terms and definitions
Magnitude and impact of counterfeiting
Counterfeit electronic part examples
G-19 Committee and its challenges
AS5553 structure
Requirements
Counterfeit electronic parts control plan
Parts availability
Purchasing processes
Procurement contract requirements
Verification of purchased product
Control of suspect or confirmed counterfeit parts
Reporting
Future G-19 plans
Counterfeit Parts Recognition
Terms and definitions
Types of counterfeits
E-Waste
Documentation review
Slides of counterfeit parts and their features
Non-destructive and destructive testing for counterfeits
Hands-on inspection with microscopes
Closing
Assessment
Evaluations
Instructor(s): Phil Zulueta and Katherine Whittington Phil Zulueta manages the Hardware Technology Assurance Group at the Jet Propulsion Laboratory, where he leads a team of engineers and technologists involved in Electronics Packaging Assurance Technologies, Non-destructive Evaluation, Electronics Manufacturing Technology Transfer (Training) and Certification, Electronics Inspection, Optical Metrology and Electro-Static Discharge (ESD) Awareness and Control. He is a JPL Program Element Manager for the NASA Electronic Parts and Packaging (NEPP) Program, facilitates the Counterfeit Parts Working Group meetings at JPL and Chairs the SAE G-19 Counterfeit Electronic Parts Committee. He is also a Past-President of the International Microelectronics and Packaging Society (IMAPS). Prior to joining JPL, he was Western Regional Manager for Electro-Science Laboratories, a Program Manager for Ball Aerospace, an Engineering Group Manager for Hughes Microelectronics in Newport Beach, CA and a Microelectronics Process Engineer for Northrop Electronics. His education includes an MBA from Pepperdine University and a B.S. in Materials Engineering from California State University Long Beach. Katherine Whittington is a Staff Engineer in the Electrical Parts Engineering organization at the Jet Propulsion Laboratory. She works as an analog parts specialist, and has been teaching a counterfeit parts awareness class at JPL since 2008. She has been a member of JPL's Counterfeit Parts Working Group (CPWG) since 2007. She holds a B.S. in Physics from UC Berkeley. She has extensive flight experience and holds an Airline Transport Pilot certificate.
Fees: $785 ; SAE Members: $695 .7 CEUs
To register, click Register button at the top of this page and submit the online form, or contact SAE Customer Service at 1-877-606-7323 (724/776-4970 outside the U.S. and Canada) or at mailto:CustomerService@sae.org?subject=Web.
For a quote on bringing this course to your company site, fill out a Corporate Learning Solutions Request Form
To register, click Register button at the top of this page and submit the online form, or contact SAE Customer Service at 1-877-606-7323 (724/776-4970 outside the U.S. and Canada) or at mailto:CustomerService@sae.org?subject=Web.
For a quote on bringing this course to your company site, fill out a Corporate Learning Solutions Request Form
If you want to learn more about how to Combat Counterfeits call Electronic Supply Chain Solutions @ 727-723-8255
